Haynes 188 Filler Wire

Metracore Alloys Private Limited manufactures and supplies Haynes 188 filler wire to fabricators, aerospace component makers and turbine overhaul units across India and in export markets. Our stock covers TIG cut lengths, MIG spools, reels and coils, so the supply form matches the welding process. Haynes 188 filler wire is a welding consumable made of cobalt, nickel, chromium, and tungsten, with the UNS designation R30188 and supplied according to AMS 5801. Welders use it to join and repair components that sit inside hot, oxidising gas streams.

Composition drives the behaviour. The wire carries 20 to 24% nickel, 20 to 24% chromium and 13 to 16% tungsten, plus a lanthanum addition of 0.02 to 0.12% that anchors the protective chromium oxide film. Deposits hold oxidation resistance up to 1095°C on prolonged exposure and resist sulphate deposit hot corrosion, the failure mode that degrades combustor hardware. Minimum tensile strength is 791 MPa (115,000 psi), with minimum elongation of 39%. 

Diameters start at 0.76 mm and reach 4.70 mm, with standard TIG straight lengths at 914 mm. Aerospace combustors, flame holders, and exhaust hardware account for most demand, with power generation repairs for turbines close behind. Every despatch carries a mill test certificate traceable to the heat number.

Send your welding procedure reference and required diameter for a stock check.

Why Choose Metracore Alloys Private Limited for Haynes 188 Filler Wire?

We hold Haynes 188 filler wire across the full 0.76 mm to 4.70 mm range in TIG cut lengths, MIG spools, reels and coils. Material arrives against AMS 5801, and we verify chemistry on receipt.

Documentation travels with the goods: mill test certificate, certificate of conformity, and heat or lot traceability back to the melt. Wire ships in sealed packaging, since surface condition affects weld cleanliness.

Bulk quantities, part-spool splits and custom-cut lengths are arranged against written requirements for domestic and export consignments alike.

Send your diameter, form and quantity for a quotation against current stock.

Haynes 188 Filler Wire Specifications

The table below sets out the commercial and technical parameters that buyers quote in enquiries for this consumable.

Types

Product Type

TIG filler wire, MIG welding wire, filler rods

Dimensions

Grade & Designations

Haynes 188 — UNS R30188, Werkstoff 2.4683

Size

Wire Diameter

0.76 mm to 4.70 mm

Standard

Standards

AMS 5801; no AWS A5.14 classification

Haynes 188 Filler Wire Types

Tig Filler Wire

Haynes 188 TIG Filler Wire

Mig Filler Wire

Haynes 188 MIG Welding Wire

Welding Filler Wire

Haynes 188 Filler Rods

Welding Filler Wire

Haynes 188 Welding Wire

Reach out to Metracore Alloys Private Limited for ready stock of Haynes 188 Filler Wire

Technical Details of Haynes 188 Filler Wire

Haynes 188 Filler Wire Specifications

The table below sets out the commercial and technical parameters that buyers quote in enquiries for this consumable.

SpecificationDetails
MaterialCobalt-based alloy (Co-Ni-Cr-W)
GradeHaynes 188 / Alloy 188
UNSR30188
Werkstoff No.2.4683
Product TypeFiller wire, filler rod
Welding ProcessGTAW (TIG), GMAW (MIG)
Wire Diameter0.76 mm to 4.70 mm
FormMIG spool, TIG cut length, reel, coil
StandardAMS 5801
Straight Length914 mm standard; other lengths on request
Minimum Tensile Strength791 MPa (115,000 psi)
Minimum Elongation39%
SurfaceClean, bright, drawn finish
TestingChemical analysis, tensile test, dimensional check
CertificationMill test certificate, certificate of conformity

AMS 5801 sits above AWS A5.14 for this alloy, because that classification covers nickel-base consumables rather than cobalt-base wire. The specification applies across every diameter from 0.76 mm to 4.70 mm.

AMS 5801 fixes the following composition limits. Cobalt makes up the balance.

ElementContent (%)
CobaltRemainder
Nickel20.0 to 24.0
Chromium20.0 to 24.0
Tungsten13.0 to 16.0
Iron3.0 max
Manganese1.25 max
Silicon0.20 to 0.50
Carbon0.05 to 0.15
Lanthanum0.02 to 0.12
Phosphorus0.02 max
Sulphur0.015 max
Boron0.015 max

Tungsten provides the solid-solution strengthening, while chromium and the lanthanum addition keep the protective oxide film adherent through thermal cycling.

Six properties explain why designers specify this consumable over cheaper fillers.

  • High-temperature strength: Solid-solution strengthening from 13 to 16% tungsten holds load-bearing capability where austenitic fillers creep.
  • Oxidation resistance: Chromium at 20 to 24% forms a protective scale, and lanthanum keeps it adherent through thermal cycling to 1095°C.
  • Hot corrosion resistance: Weld deposits resist sulphate attack in turbine hot sections burning sulphur-bearing fuel.
  • Thermal stability: The alloy retains ductility after long ageing exposure rather than becoming embrittled.
  • Weldability: Good restraint welding behaviour allows repair on assembled hardware.
  • Elevated-temperature service: Deposits earn their cost above 650°C; below that, austenitic or nickel fillers provide adequate life.

Haynes 188 Filler Wire Welding Processes

Filler Wire Manu

Haynes 188 Filler Wire Standards

AMS 5801 governs Haynes 188 filler wire as a welding consumable, covering its chemistry, mechanical minimums, and wire condition. UNS R30188 identifies the alloy, and Werkstoff 2.4683 carries the European equivalent.

AMS 5608 covers 188 sheets, strips and plates; AMS 5772 covers bar, forgings and rings. Neither applies to filler wire, and quoting them on a consumable order creates a certification mismatch at goods inward. The applicable document follows the welding process, filler form and approved procedure.

Why Choose Metracore Alloys Private Limited?

We hold Haynes 188 filler wire across the full 0.76 mm to 4.70 mm range in TIG cut lengths, MIG spools, reels and coils. Material arrives against AMS 5801, and we verify chemistry on receipt. Documentation travels with the goods: mill test certificate, certificate of conformity, and heat or lot traceability back to the melt. Wire ships in sealed packaging, since surface condition affects weld cleanliness. Bulk quantities, part-spool splits and custom-cut lengths are arranged against written requirements for domestic and export consignments alike. Send your diameter, form and quantity for a quotation against current stock.

Haynes 188 Filler Wire Sizes

Standard wire diameters cover 0.76, 0.80, 0.89, 1.00, 1.10, 1.20, 1.60, 2.00, 2.40, 3.20, 4.00 and 4.70 mm.

Filler rods follow the same diameter series, cut to a standard 914 mm straight length. MIG spool supply stops below 3.20 mm, so heavier diameters move onto reels, and coils carry the two largest sizes. Confirm spool and coil weights at the enquiry stage, since packing varies by diameter.

Applications of Haynes 188 Filler Wire

Exporter, Manufacturer & Supplier of Haynes 188 Filler Wire in various sizes and forms.

Haynes 188 Filler Wire FAQs

What is the UNS number of Haynes 188 filler wire?

Haynes 188 filler wire carries UNS R30188. The same alloy holds Werkstoff number 2.4683 under the European system.

Twelve standard diameters cover 0.76 mm to 4.70 mm. TIG straight lengths measure 914 mm, with others cut to order.

Yes. GTAW is the primary process for this consumable, particularly in combustor and duct repair, where heat input control governs weld quality.

GMAW works well with spooled Haynes 188 wire on heavier sections needing higher deposition. Diameters of 3.20 mm and above aren’t available on MIG spools.

Gas turbine combustors, flame holders, transition ducts and afterburner liners account for most usage across aerospace, defence and power generation.

AMS 5801 is the governing specification for the welding wire form. AWS A5.14 does not apply, since it covers nickel-base consumables rather than cobalt-base alloys.

Each consignment ships with a mill test certificate showing chemical and mechanical results, plus a certificate of conformity and heat or lot traceability.

Share the diameter, supply form and quantity with any specification reference, and we will confirm stock position and lead time.

Scroll to Top